This patch moves the files relevant to transcoding from
src/osmo-bsc_mgcp to src/libmgcp and src/include/openbsc. Makefiles
and include directives are being updated accordingly.
Sponsored-by: On-Waves ehf
The code currently uses an encoded sequence of (hex) 10 20 30 40 50
60 as RAI, for which no bijective mapping to the set of
representations MCC-MNC-LAC-RAC exists.
This patch changes the hard-coded RAI to 11 22 33 40 50 60 which maps
to 112-332-16464-96 (and vice-versa).
Sponsored-by: On-Waves ehf
This addresses an ASAN issue where the request was already deleted
by our callback function.
(gdb) where
#0 0xb69e7810 in __asan_report_error () from /usr/lib/i386-linux-gnu/libasan.so.0
#1 0xb69e0aff in __asan_report_store4 () from /usr/lib/i386-linux-gnu/libasan.so.0
#2 0x0804ea64 in subscr_send_paging_request (subscr=subscr@entry=0xb5103cb0)
at gsm_subscriber.c:212
#3 0x0804edac in subscr_get_channel (subscr=subscr@entry=0xb5103cb0, type=type@entry=2,
cbfn=cbfn@entry=0x804969d <subscr_cb>, param=param@entry=0x2342) at gsm_subscriber.c:246
#4 0x080498f7 in main (argc=1, argv=0xbffff804) at channel_test.c:77
Breakpoint 3, subscr_paging_dispatch (hooknum=hooknum@entry=101, event=event@entry=200,
msg=msg@entry=0x1323, data=<optimized out>, data@entry=0x8063900 <s_conn>,
param=<optimized out>, param@entry=0xb5103cb0) at gsm_subscriber.c:126
126 llist_del(&request->entry);
(gdb) b llist_del
(gdb) bt
#0 subscr_paging_dispatch (hooknum=hooknum@entry=101, event=event@entry=200,
msg=msg@entry=0x1323, data=<optimized out>, data@entry=0x8063900 <s_conn>,
param=<optimized out>, param@entry=0xb5103cb0) at gsm_subscriber.c:126
#1 0x0804e8a9 in subscr_paging_cb (hooknum=101, event=200, msg=0x1323,
data=0x8063900 <s_conn>, param=0xb5103cb0) at gsm_subscriber.c:187
#2 0x080497e9 in paging_request (bts=0xb5b03e70, subscriber=subscriber@entry=0xb5103cb0,
type=2, cbfn=cbfn@entry=0x804e881 <subscr_paging_cb>, data=data@entry=0xb5103cb0)
at channel_test.c:51
#3 0x0804ea39 in subscr_send_paging_request (subscr=subscr@entry=0xb5103cb0)
at gsm_subscriber.c:207
#4 0x0804edac in subscr_get_channel (subscr=subscr@entry=0xb5103cb0, type=type@entry=2,
cbfn=cbfn@entry=0x804969d <subscr_cb>, param=param@entry=0x2342) at gsm_subscriber.c:246
#5 0x080498f7 in main (argc=1, argv=0xbffff804) at channel_test.c:77
(gdb) q
In ae1997248c the handwritten tokenizer
was replaced with strtok_r. As part of this change the structural
checking of MGCP parameters was stopped. This means that a code like
"line + 3" might access beyond the first NUL and be possibly behind
the msgb. Manually add size checking again. Manually jumping to the
error label is not possible anymore as it has been removed. The result
is that invalid lines will be skipped. This is matching the general
approach by the IETF RFCs to be permissive in data being received.
This patch adds the voice muxer. You can use this to batch RTP
traffic to reduce bandwidth comsuption. Basically, osmux transforms
RTP flows to a compact batch format, that is later on decompacted
to its original form. Port UDP/1984 is used for the muxer traffic
between osmo-bsc_nat and osmo-bsc_mgcp (in the BSC side). This
feature depends on libosmo-netif, which contains the osmux core
support.
Osmux is requested on-demand via the MGCP CRCX/MDCX messages (using
the vendor-specific extension X-Osmux: on) coming from the BSC-NAT,
so you can selectively enable osmux per BSC from one the bsc-nat.cfg
file, so we have a centralized point to enable/disable osmux.
First thing you need to do is to accept requests to use Osmux,
this can be done from VTY interface of osmo-bsc_nat and
osmo-bsc_mgcp by adding the following line:
mgcp
...
osmux on
osmux batch-factor 4
This just initializes the osmux engine. You still have to specify
what BSC uses osmux from osmo-bsc_nat configuration file:
...
bsc 1
osmux on
bsc 2
...
bsc 3
osmux on
In this case, bsc 1 and 3 should use osmux if possible, bsc 2 does
not have osmux enabled.
Thus, you can selectively enable osmux depending on the BSC, and
we have a centralized point for configuration from the bsc-nat to
enable osmux on demand, as suggested by Holger.
At this moment, this patch contains heavy debug logging for each
RTP packet that can be removed later to save cycles.
The RTP ssrc/seqnum/timestamp is randomly allocated for each MDCX that
is received to configure an endpoint.
Add the control interface with no hierachy right now and implement
the first command to list IMSI + Context Address of active sessions.
sgsn_cmd_handle could share more code with bsc variant.
Fixes: SYS#264, SYS#265
Sadly there is no proper foreign key relationship on the tables
that related to the Subscriber. This means we can't use a DELETE
with Cascade and need to delete everything by hand. To make things
worse maybe the SMS/Paging code is still using the subscriber
making the operation more dangerous. I had added NULL checks for
sender_id/receiver_id at 30C3 so we should not crash in this
situation.
Fixes: SYS#274
The test has been manually verified. Executing the select for
the subscribers showed:
sqlite> select * from Subscriber;
1|2014-03-23 12:12:46|2014-03-23 12:19:09|2620345||445567|1||0|
This created a subscriber with the right IMSI, MSISDN and has
it authorized.
Fixes: SYS#275
The new definitions are: half rate and AMR
Change of definition name for bad frame, because it applies to all types of
traffic, not only TCH/F.
Increase MNCC interface version to 4. Version 3 is skipped, because it was
used by older version of Linux-Call-Router which is incompatible with the
current version of the MNCC interface.
Send the two strings that caused the read handling to misbehave.
Verify that we handle this correctly by still being able to issue
a VTY command. The CPU load issue could not be verified like this.
Make sure that bsc_gsmnet->bsc_data->rf_ctrl is initialized for
NITB. In commit a9fae1ae66 the
conditions for the rf_ctrl was removed but it was still needed
for the NITB.
Fixes regression from:
a9fae1ae66
bsc: rf_ctrl will always be created, remove the NULL checks
Each RP-DATA should have a unique msg reference. Currently 42 is
used for all of these. Remember the last reference we used and
increment it on the next SMS. Do not track if the reference is
still in use a clash is a lot less likely now. First unless SMPP
is used only one SMS is delivered at a time, second the transaction
space is a lot smaller than the one for the reference.
With the current multiplication we might end up with 19999 as
time on i386. When we round it ends up as 20000 on i386 and
should work the same on AMD64.
Should fix on AMD64:
mgcp_test.c: In function ‘sendto’:
mgcp_test.c:318:10: warning: format ‘%d’ expects argument of type ‘int’, but argument 5 has type ‘size_t’ [-Wformat]
So far, the jitter computation has been based on output timestamps.
This patch uses the input timestamps instead and resets jitter
computation on SSRC changes.
Sponsored-by: On-Waves ehf
Currently, when the SSRC changes within a stream and SSRC fixing is
enabled, the RTP timestamp between the last packet that has been
received with the old SSRC and the first packet of the new SSRC
is always incremented by one packet duration.
This can lead to audio muting (at least with the nanoBTS) when the
wallclock interval between these packets is too large (> 1s).
This patch changes the implementation to base the RTP timestamp offset
on the wallclock interval that has passed between these two packets.
Ticket: OW#466
Sponsored-by: On-Waves ehf
Currently micro-secs and RTP rate get mixed when the transit value is
computed in mgcp_patch_and_count().
This patch changes get_current_ts() to accept the desired rate as
argument and to use it for the time conversion instead of always
converting to microseconds. If microseconds are needed,
get_current_ts(1000) can be used.
The arrival_time is now measured in 1/rtp_end->rate seconds so that
it can be directly compared to RTP timestamps as required by RFC3550
(section 6.4.1, see definition of 'interarrival jitter').
Sponsored-by: On-Waves ehf
Currently the stats (jitter, transit) cannot be checked properly,
since they depend on the wallclock time.
This patch fakes clock_gettime (CLOCK_MONOTONIC) to reflect the
scheduling time of the RTP packets. In addition, the RTP statistical
value are written to stdout.
A RTP test case with a SSRC change along with a reference time delay
has been added.
Sponsored-by: On-Waves ehf
Currently the conn_mode and the output_enabled flags are printed to
stdout.
This patch modifies this to print the output_enabled flags to stderr
instead. The bits in conn_mode are shown as RECV, SEND, and LOOP.
This does not reduce the significance of the test, since there is an
assertion already that verifies the values of the output_enabled
flags with respect to the conn_mode.
Sponsored-by: On-Waves ehf
The filtering architecture already allowed to specify a reject
reason but this has not been used for the access-lists. Extend
the access-list to include a reject reason and extend the test
case to honor it.
Currently, the conn_mode field is reset after it has been checked.
This patch disables this behaviour and only adds a mark (bit) to
detect modifications.
Sponsored-by: On-Waves ehf
This patch changes implementation and the mgcp_connection_mode enum
in a way that net_end.output_enabled (bts_end.output_enabled) flag
always matches the MGCP_CONN_SEND_ONLY (MGCP_CONN_RECV_ONLY) bit of
conn_mode.
Based on this, the conn_mode bits are then used instead of the
output_enabled fields within mgcp_protocol.c.
Sponsored-by: On-Waves ehf
Currently RTP output_enabled is set to 1 on initialisation, which
does not semantically match the initial value of conn_mode
(MGCP_CONN_NONE).
This patch changes this initial value to 0.
Sponsored-by: On-Waves ehf
This patch (hopefully) fixes the new defects reported by coverity.
Addresses:
** CID 1156986: Negative array index read (NEGATIVE_RETURNS)
/tests/gsm0408/gsm0408_test.c: 419 in test_si_range_helpers()
/tests/gsm0408/gsm0408_test.c: 423 in test_si_range_helpers()
/tests/gsm0408/gsm0408_test.c: 427 in test_si_range_helpers()
** CID 1156987: Unchecked return value from library
(CHECKED_RETURN)
/src/libmgcp/mgcp_protocol.c: 1150 in mgcp_keepalive_timer_cb()
** CID 1156988: Unchecked return value from library
(CHECKED_RETURN)
/src/libmgcp/mgcp_protocol.c: 983 in handle_modify_con()
Sponsored-by: On-Waves ehf
So far, a single dummy packet has been sent immediately after the
reception of a MDCX message. There is no dedicated keep alive
mechanism (it just worked because the audio from the MS has always
been forwarded to the NAT until the 'mgcp: Set output_enabled flags
based on the MGCP mode' patch).
This patch adds explicit, timer based keep alive handling that can be
enable per trunk. A VTY command 'rtp keep-alive' command is added for
configuration which can be used to set the interval in seconds, to
send a single packet after the reception of a CRCX/MDCX when RTP data
from the net is expected ('once'), or to disable the feature
completely ('no rtp keep-alive'). In 'send-recv' connections, only
the initial packet is sent if enabled (even when an interval has been
configured). The default is 'once'.
Note that this removes the mgcp_change_cb() from mgcp_main.c.
Sponsored-by: On-Waves ehf
This patch extends the test_messages test to show the number of dummy
packets that has been passed to sendto(). This way, dummy packets are
even being counted when sendto() itself failes (e.g. due to the fd
being -1).
Sponsored-by: On-Waves ehf
This modifies the test MGCP messages to include M:recvonly (CRCX),
M:sendrecv (MDCX) and M:sendonly (MDCX) outputs the resulting
output_enabled flags and the conn_mode after processing the message.
Sponsored-by: On-Waves ehf
This commit adds the implementation of these range formats to the
encoder. In addition, the work-around that tried range 512 first is
removed, so that the selection is primarily based on the max distance
between frequencies.
Ticket: OW#1061
Sponsored-by: On-Waves ehf
f0 is currently set to arfcns[0] in range_enc_determine_range(),
while GSM 04.08 requires f0 to be ARFCN 0 in range1024 encoding.
This patch modifies range_enc_determine_range() to force f0 to be 0
if this encoding is used. This way the case distinction in
range_enc_filter_arfcns() is not longer necessary.
Sponsored-by: On-Waves ehf
Currently tests covering features of the GSM 04.08 specification are
spread over the si and gsm0408 subdirs in tests.
This commit merges all tests from 'si' into 'gsm0408' and removes the
'si' test sub-directory.
Sponsored-by: On-Waves ehf
This commit adds test range encoding tests. They check the property
decoding(encoding(L)) = L and optionally dump the results and
encoded sequences to stdout.
There a 2 test modes:
- A list of fixed tests
- A random number based test loop per ARFCN list size (only dumps
the first failing test)
Sponsored-by: On-Waves ehf
The iPhone5 (US) appears to have some issues with the SIs generated,
or the nanoBTS is not sending them correctly.
Add a configurable hack to put all bands into the SI2/SI5 message.
It is enabled by the bts VTY command 'force-combined-si'.
This is a quick change without much reflection and watching for side
effects. I have verfied that a network with ARFCN 134 and neighbors
ARFCN 130 and 512 do not get generate the SI2ter and announce everything
inside the SI2.
This patch is conceptually based on 'si: Add a hack to disable
SI2ter/SI2bis/SI5ter/SI5bis messages' (692daaf2d2).
Ticket: OW#1062
Sponsored-by: On-Waves ehf
Avoid a crash when reading a SMS and a Subscriber could not be resolved.
It is not clear why the read was failing. The sender_id and the receiver_id
was valid for the given sms. I assume that the database has been locked
due external access to it.
The side-effect is that in case of such a failure the sms_queue will start
to deliver starting from subscriber id = 0 again.
#1 0x0000000000428bec in sms_from_result (net=0x156a270, result=0x15eda30) at db.c:1146
#2 0x000000000042a8e0 in db_sms_get_unsent_by_subscr (net=0x156a270,
min_subscr_id=<optimized out>, failed=<optimized out>) at db.c:1255
#3 0x000000000042e900 in take_next_sms (smsq=<optimized out>) at sms_queue.c:193
#4 sms_submit_pending (_data=0x158e300) at sms_queue.c:227
#5 0x00007f3fd30de3bc in osmo_timers_update () at timer.c:243
#6 0x00007f3fd30de69b in osmo_select_main (polling=0) at select.c:133
#7 0x0000000000406fbc in main (argc=9, argv=<optimized out>) at bsc_hack.c:346
(gdb) frame 1
#1 0x0000000000428bec in sms_from_result (net=0x156a270, result=0x15eda30) at db.c:1146
1146 strncpy(sms->src.addr, sms->sender->extension, sizeof(sms->src.addr)-1);
(gdb) p *sms
(gdb) p sms->sender
$1 = (struct gsm_subscriber *) 0x0
(gdb) p sender_id
$2 = <optimized out>
Jacob Erlbeck