This dates back to a time where osmo-bsc_nat was in the same repository,
which is a long time ago.
Change-Id: Id965295dfe04f8bd5ce831db70c86f67b8dc290b
Make build and external tests work with python3, so we can drop
the python2 dependency.
This should be merged shortly after osmo-python-tests was migrated to
python3, and the jenkins build slaves were (automatically) updated to
have the new osmo-python-tests installed.
Related: OS#2819
Depends: osmo-python-tests I3ffc3519bf6c22536a49dad7a966188ddad351a7
Change-Id: I438ca0c4b8e7957d0f347a5b2f5c4cb93f9325e6
Lots of times, the MS power class is unknown until after the first
channel has been activated, at which point the MS power class is
received in messages such as LU update or CM Service Requet.
Since the MS Power level is sent upon CHAN ACT, the only way to
communicate the change of maximum MS Power (based on MS power class)
after CHAN ACT is to send a MS Power Control msg. Let's do that.
Related: OS#4244
Change-Id: I3d6b75578e5cb9b2ad474a0ad01362d846ebe135
This adds code to handle CBSP (Cell Broadcast Service Protocol)
from the CBC (Cell Broadcast Centre), as well as BSC-internal data
structures for scheduling the various SMSCB on the CBCH of each BTS.
There are currently one known shortcoming in the code: We don't yet
verify if keepalives are received within repetition period.
Change-Id: Ia0a0de862a104d0f447a5d6e56c7c83981b825c7
Fix neighbor config to match OsmoBSC manual: implement the plan for neighbor
configuration that was so far only described in the manual without actually
being in operation.
This first allows re-using ARFCN+BSIC pairs in and across BSS.
So far the handover_start() code always looked for handover target cells across
*all* local cells, even if they were not listed as neighbors to a source cell.
Imply all cells as neighbors only as long as there are no explicit neighbors
configured. As soon as the first 'neighbor' line appears in a 'bts' config,
only the listed neighbors are regarded as handover target cells. (The
'neighbor-list' commands are not related to this, only the relatively new
'neighbor (bts|lac|cgi|...)' commands affect actual handover procedures.)
TTCN3 tests TC_ho_neighbor_config_1 thru _7 play through the various aspects of
neighbor configuration: both the legacy implicit all-cells-are-neighbors as
well as allowing only explicit neighbors by config.
Related: OS#4056
Related: osmo-ttcn3-hacks Ia4ba0e75abd3d45a3422b2525e5f938cdc5a04cc
Change-Id: I29bca59ab232eddc74e0d4698efb9c9992443983
This is required for an upcoming TTCN3 test that plays through various neighbor
configurations.
Related: OS#4056
Ia4ba0e75abd3d45a3422b2525e5f938cdc5a04cc (osmo-ttcn3-hacks)
Change-Id: I8623ab581639e9f8af6a9ff1eca990518d1b1211
When we add an EARFCN to to the SI2quater struct we do not add Serving
Cell Priority Parameters. This essentially causes to MS to ignore the
EARFCN because it is still undefined under which conditions the MS
should change to LTE.
Related: SYS#4510
Change-Id: I7eaf7de4386fe8aea404e8a187d8a1f5ed596ead
bsc_clear_request() is in fact used only within gsm_08_08.c, make it static to
that file.
Since the gscon FSM, "real" BSSMAP Clear are sent only by gscon_bssmap_clear().
bsc_clear_request() remains in use for legacy code paths in gsm_08_08.c:
- the bsc_filter, i.e. for IMSI filtering;
- in move_to_msc(), from handle_cc_setup(), a code path that is in fact not
entirely clear to me. It seems to be an old functionality to serve multiple
MSCs?
Both of which I personally haven't seen in use, are not tested and should
probably be completely removed.
For now contain legacy code in the static context.
Adjust comment.
Change-Id: Ic89d0afad42e4b11183a13d2dc6b7bbf0b822fd9
Old osmo-bsc-sccplite already supported this, but in the migration
over to libosmo-sigtran and to real 3GPP AoIP, this functionality
got lost.
We now create a UDP proxy socket. Any MGCP commands received via IPA
from MSC (or rather: bsc_nat) are retransmitted to the MGW via UDP on
this socket. Any responses back from the MGW received on the UDP
socket are retransmitted back to MSC/bsc_nat as MGCP inside the IPA
multiplex.
Closes: OS#2536
Change-Id: I38ad8fa645c08900e0e1f1b4b96136bc6d96b3ab
To support the 3 possible preferences, the changes needed were:
- Replace 'full_rate' bool with a 3 option enum to represent
the channels types for signalling
- Switch from _pref/_alt to using an array sorted in preference
order
Originally merged as Change-Id I4c7499c8c866ea3ff7b1327edb3615d003d927d3,
reverted because the change broke voice calls. Re-submitting with the fix:
don't forget to set conn->assignment.requires_voice_stream.
Signed-off-by: Sylvain Munaut <tnt@246tNt.com>
Change-Id: I7513d2cbe8b695ba6f031ad11560c63a6535cf2d
osmo-mgw.git also includes fixes of the MGW endpoint FSM, for example
I92a9944acc96398acd6649f9c3c5badec5dd6dcc.
Depends: I9a3effd38e72841529df6c135c077116981dea36 (osmo-mgw)
Change-Id: I03e6b48d9b0a5370310d5f56809259ff7909cf9d
Move the T_defs API to libosmocore as osmo_tdefs: remove the local T_defs API
and use libosmocore's osmo_tdef* API instead.
The root reason is moving the mgw_endpoint_fsm to libosmo-mgcp-client to be
able to use it in osmo-msc for inter-MSC handover.
When adding osmo_tdef, the new concept of timer groups was added to the API. It
would make sense to apply group names here as well, but do not modify the VTY
configuration for timers. The future might bring separate groups (or not).
Depends: Ibd6b1ed7f1bd6e1f2e0fde53352055a4468f23e5 (libosmocore)
Change-Id: I66674a5d8403d820038762888c846bae10ceac58
When match_codec_pref() is called and the codec selections from the
ASSIGNMENT COMMAND are matched against the interal capabilities, the
configurations are checked one by one. When a match is found that match
is returned.
However, the implementation currently does not check the AMR S15-S0 bits
when the actual matching happens. This is done afterwards in case AMR
gets picked. Unfortunately if the MSC implementation is not obeying the
settings the MSC has previously communicated in the L3 COMPL message we
may end up with an S15-S0 configuration that has all rate selection
(which eventually end up as active set in RSL) bits set to zero. This is
an invalid configuration and should be prevented. Also the handling of
the S15-S0 bits should happen as part of the matching so that there is a
chance to try the nect codec in the list if AMR is unuseable.
Also S15-S0 has one special setting "Config-NB-Code = 1" (S1 = 1). When
this bit is set, the four (in HR only three) most common rates are
selected into the active set. If there are also other S-bits set besides
S1 we should prefer S1 and discard the other bits.
- Perform handling of S15-S0 while matching
- If S1 is set, prefer this setting and discard all other settings
Change-Id: Ie52376b51fe07ed07056e8df2e9557293ff67a78
Related: SYS#4470
This commit breaks voice channel assignment. It results in the
Assignment Complete sent to the MSC for a voice lchan lacking
AoIP Transport Layer Address, Speech Version and Speech Codec.
Hence the MSC cannot complete the Assignment for a voice call.
Let's revisit this patch, test thoroughly and re-merge later.
This reverts commit 4d3a21269b.
Reason for revert: <INSERT REASONING HERE>
Change-Id: I72aaa03539919e7e85b5b75b133326cec5e68bc9
To support the 3 possible preferences, the changes needed were:
- Replace 'full_rate' bool with a 3 option enum to represent
the channels types for signalling
- Switch from _pref/_alt to using an array sorted in preference
order
Change-Id: I4c7499c8c866ea3ff7b1327edb3615d003d927d3
Signed-off-by: Sylvain Munaut <tnt@246tNt.com>
When a new lchan is selected during handover, some of the properties of
the old lchan are inherited by the new lchan. At the moment S15-S0 is
not not inherited so that the value for those bits will always be 0x0000
for the new lchan. Since those bits also define the active set AMR codec
the channel activation will fail because 0x0000 is invalid (active set
with zero rates)
Change-Id: Ifd470397e99985394634da1bb13ccfc5041984d2
Related: OS#3503
When the MSC allocates a channel through the ASSIGNMENT REQUEST, it may
ask for a TCH/H and a TCH/F at the same time and tell which of the two
types it prefers.
The process of channel allocation currently selects, based on the BTS,
MSC and MS capabilites exactly one apropriate codec/rate (e.g. TCH/H)
and then tries to allocate it. If that allocation fails, there is no way
to try the second choice and the assignment fails.
For example: The MSC asks for TCH/F and TCH/H, prefering TCH/F, then the
channel allocator will try TCH/F and if it fails (all TCH/F are
currently in use), then TCH/H is never tried.
Since the BSC currently only trys the first best codec/rate that is
supported it also ignores the preference.
Lets fix those problems by including the preference information and both
possible codec/rate settings into the channel allocation decision.
Change-Id: I5239e05c1cfbcb8af28f43373a58fa6c2d216c51
Related: OS#3503
When an internal handover is done the specification demands to inform
the MSC about the event.
- Add sending of BSSMAP HANDOVER PERFORMED msg.
Change-Id: If26e5807280e0f75a423b3b04f8e3c698c82a351
Depends: libosmocore I825106858bd89afc9837811b8fed2e8accc82441
Related: OS#3645
3GPP TS 04.08 V7.21.0, section "9.1.34 System information type 2ter"
states:
"""
This message has a L2 pseudo length of 18. This message may be sent
by the network with either a L2 pseudo length of 18 or some other
value. A mobile station that does not ignore this message shall not
discard the message due to a received L2 pseudo length different
from 18.
"""
Change-Id: I45cb217ebdf89b82b0f37f38eef7a1e3a651f541
3GPP TS 04.08 V7.21.0, section "9.1.33 System information type 2bis"
states: "This message has a L2 pseudo length of 21.".
Change-Id: I623c64c446c0973e939e9f1cba0a4d4d2f4f7237
If an lchan is being released and had a SACCH active, there is no reason to
omit the Deact SACCH message ever. All of the callers that passed
do_deact_sacch = false did so for no good reason.
Drop the do_deact_sacch flag everywhere and, when the lchan type matches and
SAPI[0] is still active, simply always send a Deact SACCH message.
The do_deact_sacch flag was carried over from legacy code, by me, mainly
because I never really understood why it was there. I do hope I'm correct now,
asserting that having this flag makes no sense.
Change-Id: Id3301df059582da2377ef82feae554e94fa42035
After commit [1], the code makes sure to disassociate lchan and conn before
invoking the lchan release. However, we only send RR Release if a conn is
present, which clearly is nonsense after [1].
[1] commit 8b818a01b0
"subscr conn: properly forget lchan before release"
Change-Id: I4fd582b41ba4599af704d670af83651d2450b1db
Manage sending of RR Release via a flag, set during invoking lchan release.
Add do_rr_release arg to lchan_release(), gscon_release_lchans(). In
lchan_fsm.c, send RR Release only if do_rr_release was passed true; do not care
whether a conn is still associated (because it won't ever be since [1]).
That way we can intelligently decide what release process makes sense (whether
the lchan terminates the subscriber connection or whether the connection goes
on at another lchan), and still disassociate lchan and conn early.
BTW, this problem wasn't caught by the stock OsmoBSC TTCN3 tests, because the
f_expect_chan_rel() don't care whether an RR Release happens or not. This is
being fixed by Ibc64058f1e214bea585f4e8dcb66f3df8ead3845.
So far this patch should fix BSC_Tests_LCLS.TC_lcls_connect_clear.
Related: OS#3413
Change-Id: I666b3b4f45706d898d664d380bd0fd2b018be358
These indicators are a legacy of early handover_decision_2.c work, where there
were no separate handover1 and handover2 config commands. No need to restate
the abundantly obvious anymore.
Change-Id: Id4d29542f7dd5bd125d6f10c7783569f13092612
The commit acd29192de
Change-Id Ifb9212fede2333ad68db94188b5cda4fcabe02f8
introduced a bad change to neighbor_ident.vty. Revert that bit.
Change-Id: I8b80be6daef73f5864ba9f294bf2134c8a76ddb5
During the generation of the multirate configuration IE in the channel
activation message that is sent over RSL, all AMR rates except the
highest one are trimmed. This was to ensure that the multirate
configuration IE only contains one codec rate per active set. Lets fix
that and generate a proper IE with threshold and hysteresis values.
- extend lchan_mr_config so that it can generate a full multirate
configuration IE
Change-Id: I7f9f8e8d9e2724cbe3ce2f3599bc0e5185fd8453
Related: OS#3529
The function gsm48_multirate_config() generates the multirate
configuration IE, that is sent via RSL to configure the active set of
AMR codecs inside the BTS. The function already works, but it does not
check the input data for consistancy. Lets add some consistancy check to
make sure that inconsistant parameters are rejected. Also allow the
output pointer to be NULL, so that the function can be used to perform
a dry run to be able to verify parameters.
- Check for invalid / inconsistant configuration parameters
- Perform a dry-run when lv pointer is set to NULL
Change-Id: I06beb7dd7236c81c3a91af4d09c31891f4b910a4
Related: OS#3529
I believe I have initially misinterpreted the idea behind sending a Cell
Identifier List in BSSMAP Handover Required messages. Instead of associating N
Cell Identifiers with one ARFCN+BSIC, the idea is to add up N separate
ARFCN+BSIC's Cell Identifiers into a list. To keep the door open for future
code simplification, make sure to allow only one Cell Identifier per remote
ARFCN+BSIC on the VTY UI.
Related: OS#3656
Change-Id: Ifb9212fede2333ad68db94188b5cda4fcabe02f8
At the moment codec_pref only checks the codec configuration, but it
does not check if there is actually a matching physical channel
available. This should be checked too we must make sure that the codec
we select fits the physical channels available on the BTS.
Change-Id: I2d29dfed450e5ef93c26ed5ec9fdc0730eb3d7dd
Related: OS#3503
Opposed to all other codecs that are common in GSM, AMR requires a codec
configuration that is expressed by a bitmask (S0 to S15) in the speech
codec list in the ASSIGNMENT REQUEST. Also the BSC acknowledges those
configuration in the ASSIGNMENT COMPLETE message.
At the moment osmo-bsc ignores all incoming configuration bits. The bits
in the ASSIGNMENT COMPLETE speech codec (choosen) field are hardcoded.
- Store the configuration bits while parsing the ASSIGNMENT COMPLETE
- Create an intersection with the configuration that is actually
supported by the BSS
- Return the resulting (chosen) configuration bits with the assignment
complete message.
- Use the (highest of the) agreed codec rates in RSL channel activation.
Change-Id: I2d8ded51b3eb4c003fe2da6f2d6f48d001b73737
Related: OS#3529
Add missing item in the landscape of VTY commands: allow identifying a local
cell by CGI (besides BTS nr, LAC or LAC+CI, which already exist).
Change-Id: I2d03de6b695904c4a86025bf250358d04f6e47de
When writing the neighbor configuration documentation, I noticed that 'neighbor
add' and 'neighbor del' make sense from an interactive VTY POV, but when
looking at a static config file, it makes more sense to simply name the
neighbors without the 'add' keyword, and to use the 'no' prefix instead of the
'del' keyword. It still makes sense to tweak cosmetics like this before
inter-bsc handover is used anywhere.
First, remove 'add' from all 'neighbor add ...' commands.
Instead, prepend "Add" to the doc string for the cell identification argument
in commands that add a neighbor:
-OsmoBSC(config-net-bts)# neighbor add ?
- bts Neighbor cell by local BTS number
+OsmoBSC(config-net-bts)# neighbor ?
+ bts Add Neighbor cell by local BTS number
(A subsequent patch will rename 'neighbor del' to 'no neighbor'.)
Change-Id: I143f21f6069d1a86096cc8240cf69eb7ea9c8ac8
The COMPLETE LAYER 3 INFORMATION message lacks the Codec List (BSS Supported)
information element. This information element is mandatory for networks
that use an IP based user plane (AoIP).
- Add function to generate the speech codec list from the current codec
settings (Available codecs)
- Generate and embed information element in L3 Compl. message
Depends: libosmocore I4e656731b16621736c7a2f4e64d9ce63b1064e98
Change-Id: Id6f2af3fdab45bf05f06aec03e222734d7a4cf70
Related: OS#3548
The the function make_scl_config() is used to generate realistically
looking speech codec lists to perform the unit tests for codec_pref.c.
This function does not yet populate the S0-S15 bits for AMR codecs. Lets
make sure that at least the default configuration is populated here.
Change-Id: I534239416c038ea856c128659f314aa521f85c15
In the 'lac-ci' and 'cgi' neighbor identity VTY parameters, fix the CI part to
<0-65535>.
Use 65535 as CI in the neighbor_ident.vty test to verify the range.
Change-Id: Ie93bfe176b9d2d9445966e4ab0b928b9aa62a77f
Remove as much as possible from bsc_api.h. Use '#pragma once'. Tweak head
comment.
BSC_API_CONN_POL_{ACCEPT,REJECT}: only user is static complete_layer3(), just
use a bool return value instead.
msc_connected(): only used in osmo_bsc_api.c, make static there.
Instead of including gsm_data.h, declare structs opaquely, include stdint.h.
codec_pref_test.c used this as indirect gsm_data.h include via osmo_bsc.h,
include gsm_data.h there directly.
osmo_bsc.h: instead of including bsc_api.h, declare opaque structs.
gsm_04_08_rr.h: declare opaque structs to replace indirect include of
gsm_data.h.
Change-Id: Ia9c0f9828317236048e40ec9ecf9990592e2190a
gsm0808_page() is just a thin wrapper for rsl_paging_cmd(), the only caller is
page_ms() from paging.c. Directly call rsl_paging_cmd() instead.
Move gsm0808_cipher_mode() to the only caller in osmo_bsc_bssap.c, make static.
Change-Id: Ib7ce026b52d4ba3e53a8b2824e74ea92432c48c5
Before this patch, the timeslot FSM receives OML and RSL ready events.
Afterwards, it relies on examining the RSL and OML status to match the received
events. This doesn't work for the ip.access nanobts, which fails to change the
CHANNEL OM's operational status even though it has sent an Opstart ACK. We
receive OML CHANNEL Opstart ACK, but the mo's state left at OP_STATE=Disabled.
We apparently cannot rely on the gsm_abis_mo state as assumed before this
patch, since changing the state depends on each BTS vendor's OML
implementation.
Also, implementation wise, it is better to not include assumptions on RSL and
OML implementations in the timeslot FSM. Simply receive the OML and RSL ready
events and remember that they arrived in dedicated flags.
Remove the no longer needed oml_is_ts_ready() callback from struct
gsm_bts_model added in:
commit 91aa68f762
"dyn TS: init only when both RSL and the Channel OM are established"
I99f29d2ba079f6f4b77f0af12d9784588d2f56b3
This keeps osmo-bts operational while fixing ip.access nanobts, where the
CHANNEL OM's state prevented the timeslot FSM from entering operation.
Change-Id: I4843d03b3237cdcca0ad2041ef6895ff253d8419
Add FSMs:
- timeslot_fsm: handle dynamic timeslots and OML+RSL availability.
- lchan_fsm: handle an individual lchan activation, RTP stream and release,
signal the appropriate calling FSMs on success, failure, release.
- mgw_endpoint_fsm: handle one entire endpoint with several CI.
- assignment_fsm: BSSMAP Assignment Request.
- handover_fsm: all of intra, inter-MO and inter-MT handover.
Above FSMs absorb large parts of the gscon FSM. The gscon FSM was surpassing
the maximum amount events (32), and it is more logical to treat assignment,
handover and MGW procedures in separate FSMs.
- Add logging macros for each FSM type:
- LOG_TS()
- LOG_LCHAN()
- LOG_MGWEP(), LOG_CI()
- LOG_ASSIGNMENT()
- LOG_HO()
These log with the osmo_fsm_inst where present.
New style decision: logging without a final newline char is awkward,
especially for gsmtap logging and when other logs interleave LOGPC() calls;
we have various cases where the final \n goes missing, and also this invokes
the log category checking N times instead of once.
So I decided to make these macros *always* append a newline, but only if
there is no final newline yet. I hope that the compiler optimizes the
strlen() of the constant format strings away. Thus I can log with or without
typing "\n" and always get an \n termination anyway.
General:
- replace osmo_timers, state enums and program-wide osmo_signal_dispatch()
with dedicated FSM timeouts, states and events.
- introduce a common way to handle Tnnn timers: gsm_timers.h/.c: struct T_def.
These can be used (with some macro magic) to define a state's timeout once,
and not make mistakes for each osmo_fsm_inst_state_chg().
Details:
bsc_subscr_conn_fsm.c:
- move most states of this FSM to lchan_fsm, assignment_fsm, handover_fsm and
mgw_endpoint_fsm.
- There is exactly one state for an ongoing Assignment, with all details
handled in conn->assignment.fi. The state relies on the assignment_fsm's
timeout.
- There is one state for an ongoing Handover; except for an incoming Handover
from a remote BSS, the gscon remains in ST_INIT until the new lchan and conn
are both established.
- move bssmap_add_lcls_status() to osmo_bsc_lcls.c
abis_rsl.c:
- move all dynamic timeslot logic away into timeslot_fsm. Only keep plain send/receive functions in
abis_rsl.c
- reduce some rsl functions to merely send a message, rename to "_tx_".
- rsl_ipacc_mdcx(): add '_tx_' in the name; move parts that change the lchan state out into the
lchan_fsm, the lchan->abis_ip.* are now set there prior to invoking this function.
- move all timers and error/release handling away into various FSMs.
- tweak ipa_smod_s_for_lchan() and ipa_rtp_pt_for_lchan() to not require an
lchan passed, but just mode,type that they require. Rename to
ipacc_speech_mode*() and ipacc_payload_type().
- add rsl_forward_layer3_info, used for inter-BSC HO MO, to just send the RR
message received during BSSMAP Handover Command.
- move various logging to LOG_LCHAN() in order to log with the lchan FSM instance.
One drawback is that the lchan FSM is limited to one logging category, i.e. this moves some logging
from DRR to DRSL. It might actually make sense to combine those categories.
- lose LOGP...LOGPC logging cascades: they are bad for gsmtap logging and for performance.
- handle_classmark_chg(): change logging, move cm2 len check out of the cm3 condition (I hope that's
correct).
- gsm48_send_ho_cmd(): split off gsm48_make_ho_cmd() which doesn't send right away, so that during
inter-bsc HO we can make an RR Handover Command to send via the MSC to the remote BSS.
assignment_fsm.c:
- the Chan Mode Modify in case of re-using the same lchan is not implemented
yet, because this was also missing in the previous implementation (OS#3357).
osmo_bsc_api.c:
- simplify bsc_mr_config() and move to lchan_fsm.c, the only caller; rename to
lchan_mr_config(). (bsc_mr_config() used to copy the values to mr_bts_lv
twice, once by member assignment and then again with a memcpy.)
- During handover, we used to copy the MR config from the old lchan. Since we
may handover between FR and HR, rather set the MR Config anew every time, so
that FR rates are always available on FR lchans, and never on HR lchans.
Depends: I03ee7ce840ecfa0b6a33358e7385528aabd4873f (libosmocore),
I1f2918418c38918c5ac70acaa51a47adfca12b5e (libosmocore)
Change-Id: I82e3f918295daa83274a4cf803f046979f284366
"utils" suggests thin helpers to aid using a proper API, while this .c file
actually *is* the proper RR API. Rename from "utils" to "rr".
Change-Id: I0ffff63d57f03cb324df8e40e41caea5b55a2c85
In certain situations like handover or assignment, DTAP must not go out via RSL
directly but is cached to be submitted later. Make sure that all RSL DTAP
sending adheres to this:
gscon_submit_rsl_dtap() is the new "public" API to request an RSL DTAP to be
sent. Depending on the gscon's state, this ends up in the cache or is sent
directly. When caching, there is no way to tell whether sending will succeed or
not, so semantically it does not make sense to even return a result code. Just
return void. Change all "public" callers to gscon_submit_rsl_dtap().
Merge gsm0808_submit_dtap() and submit_dtap() guts to gsm0808_send_rsl_dtap(),
static in bsc_subscr_conn_fsm.c: directly send DTAP, assume a conn->lchan to be
present, or otherwise trigger a BSSMAP Clear Request.
The static submit_dtap() becomes a thin convenience wrapper.
Move ho_dtap_cache* functions to bsc_subscr_conn_fsm.c and rename to
gscon_dtap_cache_* -- they are not only for handover, also for assignment.
Function gsm0808_submit_dtap() m
Introduce function gscon_submit_rsl_dtap()
Change-Id: I6ffd7aa641c8905292c769400048c96aa0949585
9-bit BSIC exist in the 3GPP specs, but we don't use them anywhere. Rather
remove that choice from the API and UI.
Change-Id: I29b92f47da2636d3a19f073755f9382fa98f9010
The vty option bts->codec-support allows the user to set the supported
codecs per BTS level. However, those values are currently only used to
make the handover decision but the logic that handles the BSSMAP
ASSIGNMENT REQUEST does not check those flags.
- Do not ignore bts->codec-support flags on BSSMAP ASSIGNMENT REQUEST
Change-Id: I285234e9c81de74d9fb9907fca2c443b08537435
Closes: OS#3361
At the moment there are three sources that may advertise a list of
supported audio codec/rate settings. There is the MS that advertises
advertises a speech codec list and the MSC that sends a channel type
information element over A and there are also settings in the bsc
configuration file that may restrict the codec/rate types that are
allowed to use.
The function match_codec_pref() looks at all of the three buckets and
selects a codec that satisfies all three. This is already a somewhat
complicated process, overit is very isolated, so lets give it its own
c-file.
Due to the lack of unit-tests it is very hard to make changes here so
lets add also unit-test to make sure that regressions are catched early.
- Put match_codec_pref() and all its helper functions into a separate
c-file.
- Add a unit test.
Change-Id: Iabedfdcec8b99a319f2d57cbea45c5e36c7b6e29
Related: OS#3361
Instead of silently setting the use count to 1, instead increment with an
explicit bsc_subsct_get(), which then logs the event along with the place that
created the subscriber.
Change-Id: Ia72f8010b7b2e1ca44e3b005c0f2c05f3eeae8d5
struct bsc_api was used to provide an abstract API for both osmo-bsc and
osmo-msc, between BSC and MSC. That's no longer needed, so get rid of it, to
prevent code turbulences it creates for no reason.
Change-Id: I3fd5888c63a0b4f95520a498320aa105a6d60579
Move all of libbsc/ into osmo-bsc/, and separate/move some implementations to
allow linking from utils/* and ipaccess/* without pulling in unccessary
dependencies.
Some utilities use gsm_network and gsm_bts structs, which already include data
structures for fairly advanced uses. Move initialization that only osmo-bsc
needs into new bsc_network_init() and bsc_bts_alloc_register() functions, so
that the leaner tools can use the old gsm_* versions without the need to link
everything (e.g. handover and lchan alloc code).
In some instances, there need to be stubs if to cut off linking "just before
the RSL level" and prevent dependencies from creeping in.
- abis_rsl_rcvmsg(): the only program currently interpreting RSL messages is
osmo-bsc, the utils are merely concerned with OML, if at all.
- paging_flush_bts(): ip.access nanobts models call this when the RSL link is
dropped. Only osmo-bsc actually needs to do anything there.
- on_gsm_ts_init(): the mechanism to trigger timeslot initialization is related
to OML, while this action to take on init would pull in RSL dependencies.
utils/ and ipaccess/ each have a stubs.c file to implement these stubs. Tests
implement stubs inline where required.
From src/utils/, src/ipaccess/ and tests/*/, link in .o files from osmo-bsc/.
In order for this to work, the osmo-bsc subdir must be built before the other
source trees. (An alternative would be to include the .c files as sources, but
that would re-compile them in every source tree. Not a large burden really, but
unless linking .o files gives problems, let's have the quicker build.)
Minor obvious cleanups creep in with this patch, I will not bother to name them
individually now unless code review asks me to.
Rationale:
1) libbsc has been separate to use it for osmo-nitb and osmo-bsc in the old
openbsc.git. This is no longer required, and spreading over libbsc and osmo-bsc
is distracting.
2) Recently, ridiculous linking requirements have made adding new functions
cumbersome, because libbsc has started depending on osmo-bsc/*.c
implementations: on gscon FSM and bssap functions. For example, neither
bs11_config nor ipaccess-config nor bts_test need handover_cfg or BSSMAP
message composition. It makes no sense to link the entire osmo-bsc to it, nor
do we want to keep adding stubs to each linking realm.
Change-Id: I36a586726f5818121abe54d25654819fc451d3bf
The TEST_SCAN_TO_MSC is completely unused, but still the code linked
bsc_scan_bts_msg() for the unused code path. This is unlikely to ever be
expanded. Remove TEST_SCAN_TO_MSC and reduce linking requirements.
(I am this close to dropping the test entirely to avoid continuous linking
annoyance, but ok, since nothing else tests timezones AFAIK, keeping it.)
Change-Id: I27521950432e412f919cde811c9473557d0ec25e
Rationale: channel_test is trivial and useless, probably only exists as a
legacy from openbsc.git.
- it tests two printf()s of "(bts=45,trx=0,ts=3,ss=4)", hardly useful.
- it tests ts_subslots() behavior for dyn ts, which will soon be replaced by a
most trivial mapping that does no longer need complex dyn ts state
evaluation (when introducing the new timeslot FSM to handle dyn TS switchover).
Change-Id: Ib2232da8e7fa964b92492d7b778320401dc97703
Rationale:
- All it does is compose four Paging Requests and feed it into the osmo-bsc
bssap_udt, and expects the cell identifier to be decoded properly.
- To do so it employs a comparatively huge linking effort. This linking effort
is becoming annoying in my ongoing work and is just not worth it.
- We have comprehensive cell identifier tests in ttcn3, verifying that the
proper cells are paged, and that actually for *all* cell identifier types.
Change-Id: I07cf23b66de36cfa1142a11b9f85e9c0190ee314
The bsc_msc_connection dates back to the old pre-libosmo-sigtran
days, and 90% of the field members weren't used at all (even the
new sigtran specific ones!). Let's merge what remains into struct
bsc_msc_data.
As a side effect, the already dysfunctional "dest A.B.C.D" VTY
command has been removed from the MSC node.
There's quite a bit of fall-out in the CTRL interface, which was
the code with strongest ties to bsc_msc_connection. This was
resolved by properly porting CTRL handling over to libosmo-sigtran,
meaning that an IPA/SCCPlite connected MSC can now again send CTRL
GET/SET commands, and can also receive those selective few TRAPs
that old osmo-bsc-sccplite also sent to its MSC[s].
Change-Id: I6b7354f3b23a26bb4eab12213ca3d3b614c8154f
Related: OS#2012
osmo-bsc_nat is too heavily tied into legacy SCCPlite code, as it
is not using libosmo-sigtran/osmo_ss7 so far. It's also full of
customer-specific code and it's shared use of some libbsc code here
has been complicating osmo-bsc development.
The current plan is to continue to use osmo-bsc_nat from openbsc.git
for those legacy users that need it, and not use osmo-bsc_nat in
new 3GPP AoIP setups. Should we ever get a strong demand for an AoIP
based bsc_nat, we can still revisit this later.
Change-Id: Ia05dc76336a64a7f08962843b9a7cc19f2c83387
At this point, meas-feed is usable again, however, osmo-bsc is not able to
include the IMSI in every report like osmo-nitb did.
In consequence, the meas-vis and meas-web tools are unable to handle the
current measurement reports: these so far use the IMSI to list reports, and all
reports without an IMSI are collapsed onto the same line, swapping values.
So though osmo-bsc now sends usable measurement reports via meas-feed, two
avenues to improve should be pursued:
OS#3192: the visualization tools should use bts,ts,ss numbers, not IMSI.
OS#2969: osmo-bsc should always know a mobile identity.
Related: OS#2968
Change-Id: I186c7a995dd2b81746c32a58b55da64ed195a1ce
There is a lot of dead code in osmo_bsc_msc.c that used to handle
the IPA multiplexed SSCP lite A interface.
- remove portions of the dead code
- remove IPA Ping related VTY commands
Change-Id: I5cf3fec31cc774c902f3cfe6d16fb85ef301694a
Fix various sanitizer complaints about memory leaks using a sanitizer build
with gcc (Debian 7.3.0-12) 7.3.0.
Also fix deprecation warnings on osmo_init_logging().
Depends: I216837780e9405fdaec8059c63d10699c695b360 (libosmocore)
Change-Id: I970c6f8a0e36a8b63e42349dbc92baff649e5cef
gsm_bts_alloc() ought to do all static initialization, so that e.g. unit tests
can use an initialized bts struct that is fully usable, just not registered at
the gsm_network.
For example, two INIT_LLIST_HEAD() and various system information data pointers
(pointing to proper places within the same bts struct) should definitely never
be omitted.
This fixes the remaining errors of gsm0408_test's SI tests, as revealed by a
sanitizer build using gcc (Debian 7.3.0-12) 7.3.0.
Fixes:
../../../../src/osmo-bsc/src/libbsc/system_information.c:613:3: runtime error: null pointer passed as argument 1, which is declared to never be null
Initializing the bts->si_common.rach_control results in different expected
bytes for SI2. The initialized values are
bts->si_common.rach_control.re = 1; /* no re-establishment */
bts->si_common.rach_control.tx_integer = 9; /* 12 slots spread - 217/115 slots delay */
bts->si_common.rach_control.max_trans = 3; /* 7 retransmissions */
bts->si_common.rach_control.t2 = 4; /* no emergency calls */
Causing a change to e5 04. 04 is t2 = 4, and the remaining values are verified by:
uint8_t re :1,
cell_bar :1,
tx_integer :4,
max_trans :2;
>>> hex(1 + (9 << 2) + (3 << 6))
'0xe5'
Change-Id: I13ef24bbe0f1fbe49465e67a0b67d6fd69fff3b1
Add missing deletion of osmo_stat_item_group_free(bts->bts_statg).
Add missing bts free after test_si_ba_ind().
Log deallocation, update expected test output.
This fixes some of the errors of gsm0408_test's SI tests, as revealed by a
sanitizer build using gcc (Debian 7.3.0-12) 7.3.0.
Fixes:
=================================================================
==19273==ERROR: AddressSanitizer: heap-use-after-free on address 0x60d0000004b8 at pc 0x7f1561a94621 bp 0x7ffe7a7a64a0 sp 0x7ffe7a7a6498
WRITE of size 8 at 0x60d0000004b8 thread T0
#0 0x7f1561a94620 in __llist_add ../../../src/libosmocore/include/osmocom/core/linuxlist.h:75
#1 0x7f1561a94620 in llist_add ../../../src/libosmocore/include/osmocom/core/linuxlist.h:90
#2 0x7f1561a94620 in osmo_stat_item_group_alloc ../../../src/libosmocore/src/stat_item.c:141
#3 0x5574f6a19935 in gsm_bts_alloc ../../../../src/osmo-bsc/src/libbsc/gsm_data.c:728
#4 0x5574f6a12920 in bts_init ../../../../src/osmo-bsc/tests/gsm0408/gsm0408_test.c:123
#5 0x5574f6a0ddb3 in test_si2q_e ../../../../src/osmo-bsc/tests/gsm0408/gsm0408_test.c:192
#6 0x5574f6a0ddb3 in main ../../../../src/osmo-bsc/tests/gsm0408/gsm0408_test.c:824
#7 0x7f156061aa86 in __libc_start_main (/lib/x86_64-linux-gnu/libc.so.6+0x21a86)
#8 0x5574f6a10339 in _start (/n/s/dev/make/osmo-bsc/tests/gsm0408/gsm0408_test+0xfc339)
Change-Id: I1ebbd8cc0622ce1a061e933813829b1f770072dc
We deliberately ignore errors from page_subscriber() so there is
no point in having a non-void return value.
Provide more context in the error message logged if paging failed.
Add a comment in an implementation override of base_grace_paging_request()
in the test suite to make return value semantics more clear.
Change-Id: Ie18c2ba53d2055d3eaff8c9ed939eb844af6dd2e
Related: I48f5efbcddd98e15256edfca06ba0ae6acb5bab1
The LAI encoding test in gsm0408_test.c uses deprecated API, and a more
thorough test for LAI encoding has been added in libosmocore/test/gsm0408/.
Change-Id: I8a55d717ab15ba23943a2639accaadc33a4f731a
Fixes following compilation warning:
osmo-bsc/tests/handover/handover_test.c:48:83: warning:
‘struct mgcp_conn_peer’ declared inside parameter list will not be visible outside of this definition or declaration
int __real_mgcp_conn_modify(struct osmo_fsm_inst *fi, uint32_t parent_evt, struct mgcp_conn_peer *conn_peer);
^~~~~~~~~~~~~~
Change-Id: I1b5e91adee3daaec71122a7691a214aa8240bce2
In the current implementation of osmo-bsc, the subscriber connection is
not handled (very) statefully. However, there is some state keeping in the
code that handles the mgcp connection, but there are still to much loose ends
which allow odd situations to happen, which then lead severe error situations
(see also closes tags at the end) This commit adds a number of improvements
to fix those problems.
- Use an osmo-fsm to control the gsm_subscriber_connection state and
make sure that certain operations can only take place at certain states
(e.g let connection oriented SCCP traffic only pass when an SCCP connection
actually exists.
Remove the old osmo_bsc_mgcp.c code. Use the recently developed MGCP client
FSM to handle the MGCP connections.
Also make sure that stuff that already works does not break. This in
particular refers to the internal handover capability and the respective
unit-tests.
See also OS#2823, OS#2768 and OS#2898
- Fix logic to permit assignment to a signalling channel. (OS#2762)
- Introduce T993210 to release lchan + subscr_conn if MSC fails to respond
The GSM specs don't have an explicit timer for this, so let's introdcue
a custom timer (hence starting with 99).
This timeout catches the following situation:
* we send a SCCP CR with COMPL_L3_INFO from the MS to the MSC,
* the MSC doesn't respond (e.g. SCCP routing failure, program down, ...)
The MS is supposed to timeout with T3210, 3220 or 3230. But the BSC
shouldn't trust the MS but have some timer on its own.
SCCP would have a timer T(conn est), but that one is specified to be
1-2min and hence rather long.
See also: OS#2775
- Terminate bsc_subscr_conn_fsm on SCCP N-DISC.ind from MSC
If the MSC is disconnecting the SCCP channel, we must terminate the FSM
which in turn will release all lchan's and other state.
This makes TC_chan_rel_hard_rlsd pass, see also OS#2731
As a side-effect, this fixes TC_chan_act_ack_est_ind_refused(),
where the MSC is answering with CREF to our CR/COMPL_L3.
- Release subscriber connection on RLL RELEASE IND of SAPI0 on main DCCH
The subscriber connection isn't really useful for anything after the
SAPI0 main signalling link has been released. We could try to
re-establish, but our best option is probably simply releasing the
subscriber_conn and anything related to it.
This will make TC_chan_rel_rll_rel_ind pass, see also OS#2730
This commit has been tested using the BSC_Tests TTCN3 testsuit and the
following tests were passed:
TC_chan_act_noreply
TC_chan_act_ack_noest
TC_chan_act_ack_est_ind_noreply
TC_chan_act_ack_est_ind_refused
TC_chan_act_nack
TC_chan_exhaustion
TC_ctrl
TC_chan_rel_conn_fail
TC_chan_rel_hard_clear
TC_chan_rel_hard_rlsd
TC_chan_rel_a_reset
TC_rll_est_ind_inact_lchan
TC_rll_est_ind_inval_sapi1
TC_rll_est_ind_inval_sapi3
TC_rll_est_ind_inval_sacch
TC_assignment_cic_only
TC_assignment_csd
TC_assignment_ctm
TC_assignment_fr_a5_0
TC_assignment_fr_a5_1_codec_missing
TC_assignment_fr_a5_1
TC_assignment_fr_a5_3
TC_assignment_fr_a5_4
TC_paging_imsi_nochan
TC_paging_tmsi_nochan
TC_paging_tmsi_any
TC_paging_tmsi_sdcch
TC_paging_tmsi_tch_f
TC_paging_tmsi_tch_hf
TC_paging_imsi_nochan_cgi
TC_paging_imsi_nochan_lac_ci
TC_paging_imsi_nochan_ci
TC_paging_imsi_nochan_lai
TC_paging_imsi_nochan_lac
TC_paging_imsi_nochan_all
TC_paging_imsi_nochan_plmn_lac_rnc
TC_paging_imsi_nochan_rnc
TC_paging_imsi_nochan_lac_rnc
TC_paging_imsi_nochan_lacs
TC_paging_imsi_nochan_lacs_empty
TC_paging_imsi_a_reset
TC_paging_counter
TC_rsl_drop_counter
TC_classmark
TC_unsol_ass_fail
TC_unsol_ass_compl
TC_unsol_ho_fail
TC_err_82_short_msg
TC_ho_int
Authors:
Harald Welte <laforge@gnumonks.org>
Philipp Maier <pmaier@sysmocom.de>
Neels Hofmeyr <neels@hofmeyr.de>
Closes: OS#2730
Closes: OS#2731
Closes: OS#2762
Closes: OS#2768
Closes: OS#2775
Closes: OS#2823
Closes: OS#2898
Closes: OS#2936
Change-Id: I68286d26e2014048b054f39ef29c35fef420cc97
Until now, handover_test simply defines an abis_rsl_sendmsg() function to
override the one from libosmo-babis. To me this amounts to implicit linker
magic (aka luck).
The common pattern we're using for this scenario is to explicitly wrap an
existing function by instructing the linker. Also do this for
abis_rsl_sendmsg() in handover_test.c to clarify.
Change-Id: I05ce33a4e42bc82b9ce5060e2f811033f5a1f8d8
Add 3-digit flags and use the new RAI and LAI API from libosmocore throughout
the code base to be able to handle an MNC < 100 that has three digits (leading
zeros).
The changes to abis_test and gsm0408_test show that this code now handles
3-digit MNC correctly, by not dropping the leading zero as 0xf in the encoded
PLMN.
Re-implement CTRL commands 'mcc', 'mnc' and 'mcc-mnc-apply' to preserve the
presence of the third digit of the MNC. Always reply with all leading zeros.
Adjust the expected results in ctrl_test_runner.py, to show that it works.
In VTY and CTRL, the parsing of MCC and MNC is inherently made stricter by use
of osmo_{mcc,mnc}_from_str() -- they will no longer allow surplus characters
and detect errno returned by strtol() (in contrast to atoi()).
Depends: Id2240f7f518494c9df6c8bda52c0d5092f90f221 (libosmocore),
Ib7176b1d65a03b76f41f94bc9d3293a8a07d24c6 (libosmocore),
I020a4f11791c61742a3d795f782805f7b7e8733e (libosmocore)
Change-Id: I8e722103344186fde118b26d8353db95a4581daa
All callers pass mcc=1, mnc=1, so just have it as default.
(Prepare for net->country_code etc to be replaced by net->plmn)
Change-Id: Ic16bc0bab3f2d4721e86a1a04f9d9f988d777df2
Move from using deprecated gsm48_construct_ra(), which uses a buf, to
gsm48_encode_ra(), which uses a gsm48_ra_id argument. Pass struct gsm48_ra_id
around instead of a buf.
struct gsm48_ra_id is the "encoded" representation of the bytes in a typical
MCC-MNC-LAC-RAC (04.08 Routing Area Id IE, 3GPP TS 24.008 § 10.5.5.15). Using
the struct spares using magic numbers for byte offsets.
In the process, fix a sanitizer warning for unaligned access by using memcpy()
instead of pointer assignment:
osmo-bsc/src/libbsc/abis_nm.c:2857:27: runtime error: store to misaligned address 0x7ffe8e0d6695 for type 'uint16_t', which requires 2 byte alignment
Note that (besides removing a now unnecessary cast) the gsm0408_test and
abis_test tests of RAI / CGI encoding remain stable, which indicates that the
new code is still correct.
Change-Id: I0d3908fb8ca1e2e669d257b5d59b40675fa85d06
Expand MCC-MNC test cases: show that the CTRL interface currently does not
preserve the third digit of the MNC if it is zero. These will be fixed by
I8e722103344186fde118b26d8353db95a4581daa
Change-Id: I5b097dbb6329f284e3b4914a744d5c3ad628f715
In the past we used to set this to "-10 dBm" which means that basically
no RACH ever passed that treshold and in the associated CCCH LOAD IND
the number of busy slots was always zero.
Let's set the default to -90dBm. The user can of course always
configure a different value in the VTY.
This means that now any RACH slot signal level >= 90 dBm counts as
"busy" in those CCCH LOAD IND (RACH).
Change-Id: Ib9cbb786d19acc74f0951930b0dc9284854c6000
Closes: OS#3004
Related: OS#3003
handover_decision_2:
- lchan->conn should never be NULL, but if it is, don't crash in LOGPHO*
macros.
- make certain to avoid modulo-zero. It's cosmetic since that config item is
not allowed to be zero.
handover_test:
- check return value of gsm_generate_si().
- safer evaluation of main()'s argv.
Fixes: CID#182929, CID#182928, CID#182927, CID#182926
Change-Id: I68e8ed3a1e8659edb47ac3e8a10508f17a3f5670
Fix undefined references during link stage when building handover_test.
The archive libbsc.a needs to be listed before the various .so files.
Change-Id: Ie7e1d4815d72b8e0bbc6ccd68078a78de19d73b0
The ALIAS_DEPRECATED causes the legacy commands to no longer show up in the
command listing, hence making it more clear which commands are general and
which are for hodec1 only:
== BEFORE: ==
OsmoBSC(config-net)# list
...
handover (0|1|default)
handover algorithm (1|2|default)
handover1 window rxlev averaging (<1-10>|default)
...
handover2 window rxlev averaging (<1-10>|default)
...
handover2 retries (<0-9>|default)
handover window rxlev averaging (<1-10>|default) <-- legacy
handover window rxqual averaging (<1-10>|default)
handover window rxlev neighbor averaging (<1-10>|default)
handover power budget interval (<1-99>|default)
handover power budget hysteresis (<0-999>|default)
handover maximum distance (<0-9999>|default)
handover2 congestion-check (disabled|<1-999>|now)
OsmoBSC(config-net)# handover ?
0 Disable in-call handover
1 Enable in-call handover
default Enable/disable handover: Use default (0), remove explicit setting on this node
algorithm Choose algorithm for handover decision
window Measurement averaging settings <-- legacy
power Neighbor cell power triggering
maximum Maximum Timing-Advance value (i.e. MS distance) before triggering HO
OsmoBSC(config-net)# handover?
handover Handover general config <-- unchanged
== AFTER: ==
OsmoBSC(config-net)# list
...
handover (0|1|default)
handover algorithm (1|2|default)
handover1 window rxlev averaging (<1-10>|default)
...
handover2 window rxlev averaging (<1-10>|default)
...
handover2 retries (<0-9>|default)
handover2 congestion-check (disabled|<1-999>|now) <-- no more legacy
OsmoBSC(config-net)# handover ?
0 Disable in-call handover
1 Enable in-call handover
default Enable/disable handover: Use default (0), remove explicit setting on this node
algorithm Choose algorithm for handover decision
<-- no more legacy
OsmoBSC(config-net)# handover?
handover Handover general config <-- unchanged
The "Legacy" doc string actually never shows on the VTY console, but it will
show in the reference manual.
(Even with ALIAS(), a 'handover?' would only show the "Handover general config"
doc string, so no loss there from using ALIAS_DEPRECATED().)
Change-Id: I86be674d82242f9ca73a4d0040015c1c79f2422d
Handover decision 2 arguments are now configured by 'handover2 foo'. To match
that scheme, rename the previously 'handover foo' args for handover decision 1
to 'handover1 foo'.
For backwards compatibility, still provide aliases of the original VTY
commands. Writing back the config will result in 'handover1' though.
Change-Id: I7305ae7c04cc70082cd80d42b2ba32ffa399f51a
Do not share config items between the current handover decision and the
upcoming handover_decision_2.
Rename current handover config items to hodec2_* and duplicate the ones
relevant to handover decision algorithm 1 with name prefix of hodec1_*.
I considered moving hodec2 parameters to an entirely separate .c file and
struct, but that causes considerable code bloat. Rather use the nice
handover_cfg net/bts level mechanism as-is, and simply prefix the names.
In the VTY, the hodec1 parameters are configurable by 'handover foo 23'
commands, while the hodec2 parameters are by 'handover2 foo 23'. The generic
VTY commands to enable/disable handover and to choose the algorithm are still
'handover (0|1)' and 'handover algorithm (1|2)'.
(Note, a subsequent commit will rename the 'handover foo' for hodec1 to
'handover1 foo' and add backwards-compat aliases.)
For example, the 'window rxlev averaging 5' command now exists both for
handover decision 1 and handover decision 2, and its values are independent.
This is valid config:
network
# set up handover decision algorithm 1
# (pending rename of these items to 'handover1 ...')
handover window rxlev averaging 5
handover window rxlev neighbor averaging 5
# set up handover decision algorithm 2
handover2 window rxlev averaging 7
handover2 window rxlev neighbor averaging 7
handover2 penalty-time max-distance 10
# enable handover
handover 1
bts 0
handover algorithm 1
bts 1
handover algorithm 2
In this example, bts 0 uses algo 1 with rxlev averaging of 5, while bts 1 uses
algorithm 2 where rxlev averaging of 7 is in effect.
Change-Id: I6475b2543b18d21710a6d774b214cb484f36ec8e
About half of our log categories/subsystems were inherited from
OsmoNITB, and are no longer used but may confuse the user.
Change-Id: I8b39429f71c0faefdf8158a82093cfb19f44809e
There was always a 1:1 correspondence between gsm_subscriber_connection
and osmo_bsc_sccp_con, so there's really no point in having two separate
dynamically allocated data structures with pointers back and forth and
another linked list around.
Let's merge osmo_bsc_sccp_con into gsm_subscriber_connection for
simplicity.
The resulting code might not be elegant in places, but I've tried to
do only the most simple changes in this patch, while further
simplifications can be done in later subsequent patches.
As a side-effect, this patch also fixes lchan clearing if the MSC
(or the local SCCP provider) hard-disconnects the SCCP connection.
Change-Id: Idd2b733477ee90d24dec369755a00f1c39c93f39
Harald Welte
Oliver Smith
Pau Espin
Martin Hauke
Neels Hofmeyr
Philipp Maier
Sylvain Munaut
Neels Hofmeyr
Keith Whyte