* Increase the rewritten rule to five digits (this is the easiest
for the unit test). This will add another 40kb to the runtime size.
* Create a unit test that tests adding and removing the prefix rules.
* Use the regexp match to replace from one package
The name sccp_connection is used in the osmo-sccp code, sccp_connections
was used in the NAT for tracking a sccp_connection. Rename it so it is
obvious that the struct belongs to the nat.
The rename was done with sed:
$ sed -i s,"struct sccp_connections","struct nat_sccp_connection",g \
include/openbsc/*.h src/osmo-bsc_nat/* tests/*/*
We want to send a TRAP with the MGCP statistics from the NAT and
the connected BSC. The BSC endpoint can be either released because
of a DLCX from the MGCP CallAgent or the SCCP Connection release on
the A-link.
This is why we need to queue the statistics when the deleting the
endpoint on the BSC. The processing is continued once the response
arrives. This code assumes that the response of the DLCX will be sent
by the remote side. The current amount of outstanding responses can be
seen on the VTY. This assumption is based on the fact that the BSC has
already responded to the CRCX and maybe to the MDCX.
The MGCP RFC is bended to prefix the transaction identifier with "nat-"
to easily detect the response and hand it to the handler. This will
then parse the response and generate the TRAP. The current version is
v1. We assume that the transaction space is big enough and we will
not re-assign the transaction identifier too early.
Some nodes below 'config' didn't have ournode_exit / ournode_end,
and thus were not able to properly perform this function. exit should
always only go back one level, while end drops us back to ENABLE_NODE.
The prompt now represents the nesting level, and there's one consistent
space after the final prompt character (typically #).
Match IMSI and destination address against a set of entries, if it
is matching the header will be modified and no sender report will be
requested. Change the test case to request the sender report and then
verify that this bit is reset to 0.
Move the regexp parsing code from the NAT to libcommon as it will
be used by the NAT and BSC code. This also adds the #include <regex.h>
include to gsm_data. This header should be split up.
The idea that MCC and MNC is enough to classify a subscriber
turns out to be wrong. Certain operatos license a number range
of IMSIs to others. When we see a '^' in the MCC field we treat
it as a regexp. The code now turns the MCC/MNC into a regexp
for the IMSI. It is not using extended POSIX regexp to match
the behavior of the access list.
Introduce a paging group that a BSC can refer to and is used
during the LAC lookup. This way paging can be flooded through
the network and just filtered at the last element in the core.
Be able to configure a list of destinations (duplicates allowed)
that will be tried in a round robin fashion. The change is in
the bsc_msc_connection to operate on a list. We achieve the
round robin nature with the same trick used in the paging code
to delete and append the current entry. The nat code was updated
to compile but one can only configure one destination.
For restarting the NAT we can now block it, it will not accept
new connections and for existing connections it will attempt
to drop them over time. A blocked NAT will end up with no BSC
connections left and then can be safely restarted.
libosmogsm is a new library that is distributed in the libosmocore.
Now, openbsc depends on it. This patch gets openbsc with this
change.
This patch also rewrites all include path to the new
osmocom/[gsm|core]
Signed-off-by: Pablo Neira Ayuso <pablo@gnumonks.org>
This change is required to finish the integration of the VTY and
the per-application logging categories that provides:
"vty: integration with logging framework"
in libosmocore.
It has been tested with osmo-nitb. The other just compiled tested.
Holger Hans Peter Freyther
Harald Welte