It makes no sense to enable that field if the ext_info.egprs_supported
field marks EGPRS as disabled.
From TS 44.060 11.2.5a:
"""
This message may be sent by an EGPRS capable mobile station
*in a cell supporting EGPRS* and where the EGPRS_PACKET_CHANNEL_REQUEST
parameter indicates that this message shall be used.
"""
Related: SYS#5891
Change-Id: I5ac173116f8681d7340b75b2baff110158fab9fd
If "bts->gprs.mode" was changed dynamically at runtime (VTY or CTRL), it
could happen that the egprs_supported was kept as "1" if the dynamic
change was EGPRS->GPRS.
In summary, if EGPRS support was set, it couldn't be unset until BSC was
restarted.
Related: SYS#5894
Change-Id: Id2c2319044da474642c4cc710baa27cfee4fb592
Values in ext_info are modified in several places, so it's difficult
validating whether we deviate from default. Let's always send it so that
we always have a clear view on what the MS uses.
This fixes a bug where paging_coordination or ccn_active would not be
announced if GPRS was not enabled.
Related: SYS#5894
Change-Id: If96de3e0d77503cf6344dfbc611f9260ac3281aa
The value in bts->si_common.chan_desc may get out of sync with the
actual value in net->T_defs (e.g. after changing it via the VTY),
so we need to sync it in generate_si3().
Note that synchronizing the values in cfg_net_per_loc_upd_cmd is
a bad idea, because the value of T3212 may also be changed using
generic timer management commands.
Change-Id: Iee291623c2825505eeb5175adcedadfe35375b9e
Related: SYS#5888
This was overlooked during the code review. GCC does not complain
because internally both 'enum handover_scope' and 'bool' are
interpreted as 'int'. Found this while running my WIP testcase
TC_srvcc_eutran_to_geran_a5_3. This change makes it pass.
Change-Id: I807fd4a0e700e54c67ca3547d9c0c1b442dd1c54
Fixes: I4e5b1163a71443d706f14ce4bfd5c2294c320432
Related: SYS#5838
According to 3GPP TS 44.018, section 9.1.15, the RR Handover Command
message may optionally contain the Cipher Mode Setting IE (10.5.2.9).
Section 9.1.15.10 states that this IE may be omitted in case of the
intra-RAT GERAN-to-GERAN handover, however in case of the inter-RAT
handover (e.g. EUTRAN-to-GERAN), this IE *shall* always be included.
Change-Id: I1d270e82d0a9b12897fc94dae4e8999aa132a22f
Related: SYS#5838
When running a multi-trx setup, upon stopping osmo-bts one can see:
DCHAN ERROR lchan_fsm.c:80 lchan(0-1-7-TCH_F-0)[0x612000010120]{UNUSED}:
(type=NONE) lchan allocation failed in state UNUSED: LCHAN_EV_TS_ERROR
DCHAN ERROR lchan_fsm.c:144 lchan(0-1-7-TCH_F-0)[0x612000010120]{UNUSED}:
(type=NONE) lchan activation failed
(lchan allocation failed in state UNUSED: LCHAN_EV_TS_ERROR)
These messages show up when the following conditions are met:
* BTS model speaks A-bis over IP (ip.access, e.g. nanoBTS), and
* BTS has more than one transceiver configured.
The problem is that unlike traditional E1 based BTS models, ip.access
ones have a single global A-bis/OML link for all transceivers. Thus
when it goes down, in inp_sig_cb() we need to notify all timeslots
*of all TRXes*, not just TRX0.
Change-Id: I3dc657ac5a2c5334747bd4f4db1a658acb323942
Fixes: OS#5479
Historically, we first only had
BSS_MAP_MSG_ASSIGMENT_RQST
^
with missing N. libosmocore has this renamed a long time ago and
provides a shim #define that makes the typo version still work.
Having the typo is bad for grepping, so rather use the non-typo name.
Also rename the constant for the ass req counter which so far has a
similar typo, and fix the same typo in the counter description.
The counter name exposed on CTRL luckily doesn't have this typo in it.
Change-Id: Ieaa4f4e6e6f7e1563b1bd15a83f0c1a9112d2312
The ho_fail() macro includes a newline, so the callers should not add
one. Fix these cases where the extra '\n' fragments the logged message.
Related: SYS#5839
Change-Id: Ifdbce98be70c1aa127ae008d7a77b9795fd250d3
So far we completely ignore the codec list from the MSC in Handover
Request messages. This leads to error messages in subsequent handovers
because there is no Codec List stored on the conn:
DHODEC ERROR handover_decision_2.c:390 [...] No Speech Codec List present, accepting all codecs
Besides the error log, in hodec2 we may subsequently take bogus or
unexpected codec decisions, ignoring the MSC's choice of codecs, or in
the worst case picking an unsupported codec.
This also has implications on what type of lchan we choose for handover
target in hodec2: say, if no half rate codec is supported as per the
MSC's request, we normally avoid handover to a TCH/H, etc.
Intra-BSC HO after an Inter-BSC incoming HO is the only case where this
problem occurs, in every other scenario there is an Assignment Request
from the MSC, from which we properly store the MSC's codec list.
3GPP TS 48.008 does indicate that on AoIP this codec list shall be
included. So reject HO Request with missing Codec List, as we already do
for Assignment Request on AoIP.
This makes TTCN3 BSC_Tests for inter-BSC incoming HO fail, because our
tests so far omit the Codec List (MSC Preferred) on AoIP. The related
fix of the tests is If06de9c9b43d79f749447a4e2a340176eef75c79.
Related: SYS#5839
Depends: If06de9c9b43d79f749447a4e2a340176eef75c79 (osmo-ttcn3-hacks)
Change-Id: I117cc29d6d11db77d160de654f43f5993db6ee21
"inter-BSC MT" was the terminology of an early development stage of
inter-BSC handover, code review requested "incoming" instead. This one
was missed when applying code review.
Same in a code comment.
Related: SYS#5864
Change-Id: I1ca810542e89980ffda11876fd30626467e452d1
Teach osmo-bsc to handle empty N-Connect. So far we were always
expecting user data in an SCCP N-Connect from an MSC. However, it is
perfectly valid for an initial BSSMAP request to follow later.
This is relevant for:
- Handover Request (incoming inter-BSC handover)
- Perform Location Request (query physical location of the MS)
Add state WAIT_INITIAL_USER_DATA with new timeout net X25. Always enter
this state so that we don't have two separate code paths for handling
initial user data.
Related: SYS#5864
Change-Id: I535c791fa01e99a2226392eb05f676ba6c3cc16e
Also increment message counter for the case that a Perform Location
Request came in the initial SCCP N-Connect message.
Related: SYS#5864
Change-Id: I3f78ce73eb16fdff1f19359963405b2235000fc4
During inter-BSC incoming handover, there is no previous lchan to be
switched, so this event always comes in the READY state of
lchan_rtp_fsm. No need to complain about that and confuse log readers.
Related: SYS#5864
Change-Id: I96fd53b8c8da621a40bd65f85070eabd030cc875
According to 3GPP TS 44.018, section 10.5.2.1b.2, only ARFCN values
in range 1..124 can be encoded using the 'bit map 0' format. Before
this patch, ARFCN values belonging to E-GSM band (0, 975..1023) were
ignored in bitvec2freq_list(), and thus not present in the resulting
Cell Channel Description IE.
Change-Id: I17739e6845cd84e2a81bc406dd532541f7c52cb6
Related: SYS#5854
I find it cleaner to relay on the counter ('arfcns' in this case) to
check if the set is empty, rather than checking one of the resulting
values ('max'). There is just a cosmetic change.
Change-Id: I29ca51461beec053bcb8b8210f0ad24bb8c7765f
Related: SYS#5854
This commit demonstrates what happens when a cell has channels in
both P-GSM and E-GSM bands (case 'c'). As can be seen from:
Case a) only the BCCH carrier: 10
Case b) more carriers from P-GSM band: 1 3 10 64 99 124
Case c) more carriers from E-GSM band: 1 3 10 64 99 124
in both cases 'b' and 'c' we have the same set of ARFCNs. Carriers
from the E-GSM band are not present at all. This is wrong and will
be fixed in the follow up change(s).
Change-Id: Ied0519c70501f105673a9b36657101063d275058
Related: SYS#5854
The callers of this function do pass different mask values, which
should be passed to gsm48_decode_freq_list(). Instead, 0xce was
passed regardless of the given mask value.
Change-Id: I47f2eab54ef8487b14992fd7a69d5c9ccbb3f5cf
As the comment above the fix suggest, the encoding is in 10ms units.
osmo-bts is also doing the proper:
"""
uint8_t t3105 = *TLVP_VAL(&tp, NM_ATT_BTS_AIR_TIMER);
bts->t3105_ms = t3105 * 10;
"""
Related: SYS#5838
Change-Id: Ie190514ee35d1ca81b70e9180bf7393b973d3504
Improve the function doc. Remove a comment at a caller, because that
information is what the function doc is for.
Rename the array to codec_by_strength, because it is not the codec
strength but the codec number listed in the array.
Related: SYS#5839
Change-Id: Iaed6b97c31e4ccb1f28ca7e64596d5e20563b392
In the field we saw Handover Requests without any Chosen Encryption
Algorithm IE, and osmo-bsc completely failed on those. This made me
understand my mistake from when I wrote this handover code.
So far, from a BSSMAP Handover Request, we (I) used only the Chosen
Encryption Algorithm IE to pick the encryption to use on the target
lchan. That is very wrong.
Instead, figure out the intersection of permitted algorithms MSC & BSC,
and pick the best of those. Which means, actually, completely ignore the
Chosen Encryption Algorithm IE.
In the message, the permitted algorithms are passed as a bitmask. The
current code using gsm0808_dec_encrypt_info() passes this on as an
array. In order to select_best_cipher(), I could convert that array back
to a bitmask. Instead pass the bitmask on from message decoding
alongside the struct gsm0808_encrypt_info in req->ei_as_bitmask.
In handover_end(), change the condition so that we can also pass
HO_RESULT_FAIL_RR_HO_FAIL to emit a Handover Failure.
Related: SYS#5839
Change-Id: Iffedc981b60d309ed2e5decd5efedee07a757b53
The naming confused me so that I wrote buggy code again. Hopefully this
clarifies which representations the code paths are using.
In the macro code, highlight the error case of n <= -1 explicitly.
Also add ALG_A5_NR_TO_PERM_ALG_BITS. I need the 1<<n case in an
upcoming patch.
Related: SYS#5839
Change-Id: I7557ae97764bba09c906748a18e9031dfb362611
This patch imposes no logical change in the code on itself, but makes
sure people compiling osmo-bsc uses an old enough libosmocore
implementing Cell Identifier SAI. This is important since adding the SAI
ID (CELL_IDENT_SAI) displaced CELL_IDENT_WHOLE_GLOBAL_PS to a new
number outside of the 3GPP range for cell IDS (4 bits, this way we
garantee we won't have the same problem again).
This means there was an ABI breakage (see Depends below).
As a result, using an osmo-bsc compiled against an older libosmocore
, and then using at runtime against a newer version of libosmocore, will
most probably provoke some RIM features to not work properly, since
libosmocore will handle CGI-PS cell ids sent by osmo-bsc as SAI ones,
and most probably do wrong comparisons when matching (they only match up
to LAI included).
ABI break analysis:
osmo-bsc uses CELL_IDENT_WHOLE_GLOBAL_PS in:
* gsm0808_dec_cell_id_list2() -> this is called on stuff received from the
network, so it's actually fine handling it
correctly as CELL_IDENT_UTRAN_SAI instead
of CGI_PS.
* gsm0808_cell_id_list_add
same_cell_id_list_entries
gsm0808_enc_cell_id_list2
cell_id_to_cgi-> On old osmo-bsc, When
CELL_IDENT_WHOLE_GLOBAL_PS is passed
to be encoded as CGI, RAC byte is
taken for encoding instead of 2nd CI byte.
* gsm0808_cell_ids_match
gsm0808_cell_id_u_match
cell_id_to_cgi -> If CELL_IDENT_WHOLE_GLOBAL_PS as 0x11
(CELL_IDENT_UTRAN_SAI), 1 byte offset when
comparing (1 byte of RAC is taken converting to
CGI instead of the 2nd byte of CI). That means
match would be wrong if 2nd byte of CI differs.
Related: SYS#5838
Depends: libosmocore.git Change-Id Id25e563febdb7640174540136225f399515a0089
Change-Id: I70972efffefd57fd36332fab539683696c32f4a5
The timer (T4) that controls the re-sending of the BSSMAP RESET can not
be changed via the VTY, althrough it is defined via a tdef struct. Lets
add a description along with default values to make it configurable via
the VTY.
Change-Id: I1fb5699220ab8a643a168567a89c6f381fe433a7
Related: SYS#5796
An earlier patch version had that typedef, the merged version switched
to the struct containing the array.
Change-Id: Id8ca7b298436feb98f4a563ad3cdea510b9362b0
The SAPI "n" REJECT messages were being sent with DLCI keeping the RSL
LINK ID format, which is not the same for CC bits.
With this patch, TTCN3 test BSC_Tests.TC_rll_sapi_n_reject_dlci_cc
passes again.
Related: OS#4728
Related: SYS#5047
Change-Id: Icc187f594743040a3d9b8beff7d9cfc21dd6eb08
Skip the BSSMAP Clear and SCCP RLSD parts and immediately deallocate the
gscon when there is no SCCP connection present. Before this patch, such
conn would stick around for a minute before a timeout deallocates it.
Related: OS#5337
Change-Id: I8c8537acf6b47b121903197608636c43ae601a57
Properly implement the separate conn release stages in separate FSM
states:
x) sent Clear Request, wait for a Clear Command from the MSC.
Timeout after a configurable 60s.
y) after a Clear Command and sending a Clear Complete, wait for the SCCP
RLSD. Timeout after a configurable 60s.
z) terminate after the RLSD is received / after timeout.
handover_test.c needs a little tweak to make the MGCP release work with
its fake MGCP client, because cleanup now ensures to invoke
gscon_forget_mgw_endpoint() in all cases.
Related: I680ec4ed866aa5f0b1ff29e7e98322615cfb288d (osmo-ttcn3-hacks)
Related: OS#5337
Change-Id: Ie975117d37f38ba853589dc7f8d3e94f8f9586b2
The way the ST_CLEARING is entered before this patch has various
symptoms of how I / we used osmo_fsm when we were still FSM amateurs in
Osmocom. Patch that up:
- In gscon_bssmap_clear(), ask for a state transition to ST_CLEARING
first. Go ahead only if it is allowed.
- move the Clear Request messaging to ST_CLEARING's onenter function.
- Fix the timeout behavior: by using conn_fsm_state_chg(), use the
actual proper X4 timer value for ST_CLEARING from VTY configuration
instead of hardcoded magic numbers.
Related: OS#5337
Change-Id: I234b2a754d0c98031056981823cdbc187e977741
Allow returning a context sensitive cause instead of a hardcoded one in
gscon pre_term().
Also, the conn->cause is needed to move message dispatch to an "onenter"
function in patch I234b2a754d0c98031056981823cdbc187e977741. I Split
this part off as a separate patch for better readability.
Related: OS#5337
Change-Id: Ib6432746040899129d1d73ae8dc59add2d88a915
In lcs_ta_req_wait_ta_onenter(), fix use count leak of 'start-paging':
get() the use count only after the early exits.
osmo-ttcn3-hacks patch I69d4c5c6f8d499bb7f0b96a48af045361433c57b
introduces testing against this leak in various LCS tests (e.g.
BSC_Tests.TC_lcs_loc_req_for_active_ms_ta_req).
Related: OS#5355
Change-Id: Ibbfbfe766eafe42c78048ec5b3b503a11ef5535d
Pau Espin
Vadim Yanitskiy
Neels Hofmeyr
Philipp Maier
Neels Hofmeyr