This was overlooked during the code review. GCC does not complain
because internally both 'enum handover_scope' and 'bool' are
interpreted as 'int'. Found this while running my WIP testcase
TC_srvcc_eutran_to_geran_a5_3. This change makes it pass.
Related: SYS#5838
Fixes: I4e5b1163a71443d706f14ce4bfd5c2294c320432
Change-Id: I807fd4a0e700e54c67ca3547d9c0c1b442dd1c54
(cherry picked from commit 7c14a12a78)
According to 3GPP TS 44.018, section 9.1.15, the RR Handover Command
message may optionally contain the Cipher Mode Setting IE (10.5.2.9).
Section 9.1.15.10 states that this IE may be omitted in case of the
intra-RAT GERAN-to-GERAN handover, however in case of the inter-RAT
handover (e.g. EUTRAN-to-GERAN), this IE *shall* always be included.
Related: SYS#5838
Change-Id: I1d270e82d0a9b12897fc94dae4e8999aa132a22f
(cherry picked from commit 2902d91d69)
According to 3GPP TS 44.018, section 10.5.2.1b.2, only ARFCN values
in range 1..124 can be encoded using the 'bit map 0' format. Before
this patch, ARFCN values belonging to E-GSM band (0, 975..1023) were
ignored in bitvec2freq_list(), and thus not present in the resulting
Cell Channel Description IE.
Change-Id: I17739e6845cd84e2a81bc406dd532541f7c52cb6
Related: SYS#5854
As the comment above the fix suggest, the encoding is in 10ms units.
osmo-bts is also doing the proper:
"""
uint8_t t3105 = *TLVP_VAL(&tp, NM_ATT_BTS_AIR_TIMER);
bts->t3105_ms = t3105 * 10;
"""
Related: SYS#5838
Change-Id: Ie190514ee35d1ca81b70e9180bf7393b973d3504
(cherry picked from commit 8f1597135d)
In the field we saw Handover Requests without any Chosen Encryption
Algorithm IE, and osmo-bsc completely failed on those. This made me
understand my mistake from when I wrote this handover code.
So far, from a BSSMAP Handover Request, we (I) used only the Chosen
Encryption Algorithm IE to pick the encryption to use on the target
lchan. That is very wrong.
Instead, figure out the intersection of permitted algorithms MSC & BSC,
and pick the best of those. Which means, actually, completely ignore the
Chosen Encryption Algorithm IE.
In the message, the permitted algorithms are passed as a bitmask. The
current code using gsm0808_dec_encrypt_info() passes this on as an
array. In order to select_best_cipher(), I could convert that array back
to a bitmask. Instead pass the bitmask on from message decoding
alongside the struct gsm0808_encrypt_info in req->ei_as_bitmask.
In handover_end(), change the condition so that we can also pass
HO_RESULT_FAIL_RR_HO_FAIL to emit a Handover Failure.
Related: SYS#5839
Change-Id: Iffedc981b60d309ed2e5decd5efedee07a757b53
The naming confused me so that I wrote buggy code again. Hopefully this
clarifies which representations the code paths are using.
In the macro code, highlight the error case of n <= -1 explicitly.
Also add ALG_A5_NR_TO_PERM_ALG_BITS. I need the 1<<n case in an
upcoming patch.
Related: SYS#5839
Change-Id: I7557ae97764bba09c906748a18e9031dfb362611
This patch imposes no logical change in the code on itself, but makes
sure people compiling osmo-bsc uses an old enough libosmocore
implementing Cell Identifier SAI. This is important since adding the SAI
ID (CELL_IDENT_SAI) displaced CELL_IDENT_WHOLE_GLOBAL_PS to a new
number outside of the 3GPP range for cell IDS (4 bits, this way we
garantee we won't have the same problem again).
This means there was an ABI breakage (see Depends below).
As a result, using an osmo-bsc compiled against an older libosmocore
, and then using at runtime against a newer version of libosmocore, will
most probably provoke some RIM features to not work properly, since
libosmocore will handle CGI-PS cell ids sent by osmo-bsc as SAI ones,
and most probably do wrong comparisons when matching (they only match up
to LAI included).
ABI break analysis:
osmo-bsc uses CELL_IDENT_WHOLE_GLOBAL_PS in:
* gsm0808_dec_cell_id_list2() -> this is called on stuff received from the
network, so it's actually fine handling it
correctly as CELL_IDENT_UTRAN_SAI instead
of CGI_PS.
* gsm0808_cell_id_list_add
same_cell_id_list_entries
gsm0808_enc_cell_id_list2
cell_id_to_cgi-> On old osmo-bsc, When
CELL_IDENT_WHOLE_GLOBAL_PS is passed
to be encoded as CGI, RAC byte is
taken for encoding instead of 2nd CI byte.
* gsm0808_cell_ids_match
gsm0808_cell_id_u_match
cell_id_to_cgi -> If CELL_IDENT_WHOLE_GLOBAL_PS as 0x11
(CELL_IDENT_UTRAN_SAI), 1 byte offset when
comparing (1 byte of RAC is taken converting to
CGI instead of the 2nd byte of CI). That means
match would be wrong if 2nd byte of CI differs.
Related: SYS#5838
Depends: libosmocore.git Change-Id Id25e563febdb7640174540136225f399515a0089
Change-Id: I70972efffefd57fd36332fab539683696c32f4a5
The timer (T4) that controls the re-sending of the BSSMAP RESET can not
be changed via the VTY, althrough it is defined via a tdef struct. Lets
add a description along with default values to make it configurable via
the VTY.
Change-Id: I1fb5699220ab8a643a168567a89c6f381fe433a7
Related: SYS#5796
The checks that make sure that an ARFCN falls in the correct range do
not return with -EINVAL as they should, instead nothing happens. (Only
the check for GSM1800 is corrct)
Change-Id: Iddadafe3fbc47e2f980d8e4ab4f320998cb454ff
Related: SYS#5369
Remove the paragraph about writing to the Free Software Foundation's
mailing address. The FSF has changed addresses in the past, and may do
so again. In 2021 this is not useful, let's rather have a bit less
boilerplate at the start of source files.
Change-Id: Ifbbafe185931c0f508ff8148ef244f25a9620fd8
At the moment the BTS configuration is checked, but the check does not
have much consequence other than that some initialization that is not
executed. The BTS will go into the OML bootstrap phase anyway and most
likely fail at some later point due to the invalid configuration. To
reduce noise and unexpected behaviour of the BTS lets make sure that the
OML boostrap phase can only proceed when the BSC conciders the
configuration as valid.
Change-Id: I42c1c26a9b800600787b1266a871f95f2114c26e
Related: SYS#5369
Counting the Assignment success after osmo_fsm_inst_term() meant that we
were counting a cleared out channel mode, which always yielded
signalling mode.
Count the Assignment success *before* terminating, so that we correctly
count the successful assignment as speech mode.
Related: SYS#4878
Related: Icb1386ec2ccd70eb3c026301b9b08ad7177278f7 (osmo-ttcn3-hacks)
Change-Id: Ie9fcd1e86f27ecb2f11e2e8813faac365cb470b8
Similar to paging:attempted, count paging:expired not only per BTS, but
also for the whole BSC. Add active_paging_requests to struct bsc_subscr,
to increase the counter only once if paging expires, and not once per
BTS where paging expired.
Related: SYS#4878
Change-Id: I9c118e7e3d61ed8c9f1951111255b196905eba4d
osmo-trx-uhd with a B200 has proven to provide bad (lower than usually
considered good) C/I values due to high noise (even with band filters in
place). Hence, default thresholds (gathered from literature on the topic)
are too high and end up in bad algorithm output decisions.
Furthermore, most users of Osmocom don't use it in densely populated
areas, hence RXLEV based algorithm used when C/I based one is disabled
is good enough.
Let's disable C/I based one by default, and let advanced users which
specific needs to enable and confiure thresholds specifically for their
needs (hardware, cell surrounding conditions, etc.).
Related: SYS#4917
Change-Id: If1a73c60695379bcfcd0f44c6ec6dd659563e279
abis_nm locally declares its own struct for the ipaccess firmware
header, even though libosmocore defines it as well. Lets use the
definition from libosmocore.
Change-Id: I69cb45fc40bd20ea2533cc8cd6a68363b59cc408
The function generate_ma_for_bts() is called when the OML TEI comes up.
In the same code path boostrap_bts() is called as well. It would be more
logical to call generate_ma_for_bts() from boostrap_bts() since it is
also part of the bootstrapping process.
Change-Id: Ib2ed5b1eac3701cfb3a3e8dd478488ba5404d1fd
Related: SYS#5369
At the moment check_bts and bootstrap_bts is called only once on startup.
When a new BTS is set up during runtime bootstrap_bts, nor check_bts is
called. This means that some parameters of the BTS stay uninitalized
until osmo-bsc is restarted. Lets rather call check_bts() and then
bootstrap_bts() when the OML TEI of the BTS comes up.
Change-Id: Ie599f809623efd6ea4ab3f39294195fc1ef84b85
Related: SYS#5369
Let's have a short and consistent naming for both ACCH repetition
and temporary ACCH overpower structures, like it's done in osmo-bts.
Change-Id: I39b98dcd14219402959646524315d5afea7c08cf
Related: Ib1d51f91139b4c2fe794e37fc8543b2d7a9b9c07
Let's have a short and consistent naming for both ACCH repetition
and temporary ACCH overpower structures, like it's done in osmo-bts.
Change-Id: Ia12c83ad1af4744ce28ba655ac806784f746e88a
Related: Ib1d51f91139b4c2fe794e37fc8543b2d7a9b9c07
The linter (executed by Jenkins) complains:
src/osmo-bsc/bts_vty.c:653: ERROR:CODE_INDENT: code indent should use tabs where possible
src/osmo-bsc/bts_vty.c:654: ERROR:CODE_INDENT: code indent should use tabs where possible
src/osmo-bsc/bts_vty.c:656: ERROR:CODE_INDENT: code indent should use tabs where possible
src/osmo-bsc/bts_vty.c:657: ERROR:CODE_INDENT: code indent should use tabs where possible
and blocks changes, adding V-1 when I am changing the related code.
Change-Id: If3c8c09ddff7cb945425e74344ceb4da989ddffc
The linter (executed by Jenkins) complains:
src/osmo-bsc/abis_rsl.c:543: ERROR:POINTER_LOCATION: "(foo*)" should be "(foo *)"
and blocks changes, adding V-1 when I am changing the related code.
Change-Id: I0cf00ff898e69734850659e8ba0e2ff023f9b2dd
In the case of ts->pchan_from_config=GSM_PCHAN_OSMO_DYN,
ts->max_primary_lchans will be 8 due to SDCCH8 support, and we don't
want to set lchan->vamos.is_secondary=true for lchans at the end of the
array.
Related: OS#5278
Change-Id: If86af5fafe059d5e830c1f6d37034f7325d9a96c
The function set_bts_loc does not check the string pointers resturned by
strtok_r. In this particular case this is not a problem because the
function set_bts_lock will only see verfied input. However, lets check
the results anyway to avoid creating false positives in coverity scan.
Change-Id: Ie21c392e0405fc45811c6d55bf5508e9eb6784de
Fixes: CID#240849
In order to be able to call check_bts() and bootstrap_bts() from
inp_sig_cb(), we must move it below bootstrap_bts.
Change-Id: I1a365bc2278368ec1f5c0db3f3e466b124b16e83
Related: SYS#5369
The function bootstrap_bts does a few checks before it does the actual
initialization. To make the code more modular, lets split the function
into two functions, check_bts and bootstrap_bts. Also be sure that we
print the BTS number when the check failes.
Change-Id: Id2b26f147d2f35e156e2da8ee58d2bbbb93de4ac
Related: SYS#5369
The function bootstrap_bts verifies that the ARFCN number is within the
valid range of the current band. In case of error it prints that the
ARFCN is out of range, but it does not print the BTS number, nor the
ARFCN number.
Change-Id: I432448b4bd5ea1a209838a6c5105cc1e9f7d80ee